Skip to main content

step by step instructions for changing a fuel filter

Here are step-by-step instructions for changing a fuel filter. Before you get started, read them carefully and make sure that you want to do this job yourself.

Tools and Equipment

To change your fuel filter you will need:

  • Drive-on car ramps or jack stands (with sufficient capacity for vehicle weight). Depending on the location of your fuel filter, these may not be required. For landini tractor look at the photo below.
  • Open-end wrenches designed for use with filter connections, and pliers.
  • The correct replacement fuel filter for your specified vehicle and engine.
  • A supply of clean rags.
  • Safety glasses (required).
  • An approved container to catch spilled fuel.

    BEFORE YOU BEGIN

    • Locate the fuel filter. In most cases it's bolted to a rail on the bottom of the vehicle, ahead of the rear wheels. Refer to your vehicle's service manual 
    • The filter has two hose connections: the fuel inlet, which runs in from the fuel tank, and the fuel outlet, which runs out to the engine.
    • Make sure to note the orientation of the filter for proper installation of the new filter. Make sure the engine and exhaust system are cold. Let them sit for at least three hours.

 STEPS

Relieve the pressure in the fuel line before disconnecting it. To do so, you have to disable the electric fuel pump before you start the engine.

To disable the fuel pump, do the following:

With the engine off, remove the fuel pump fuse from the fuse box.
Make sure that the parking brake is on and that the vehicle is in Park or Neutral, and then start the engine. It won’t run very long after you start it up, but the pressure in the fuel lines will be reduced.
Turn off the engine.

 With the fuel pump disabled, you’re ready to disconnect the fuel lines from the filter.
Look at the old filter and the new one before disconnecting anything.
You should see an arrow stamped on both filters that shows in which direction the fuel flows through it. If the new one doesn’t have an arrow on it, look to see in what direction the old filter is installed so that you can tell which end of the new filter goes where.
Remove whatever is holding the old filter in place and remove it.
Put the new filter on in the same position as the old filter.
Replace whatever holds the filter in place, and make sure it’s secure.
Replace the fuse for the fuel pump in the fuse box.
Make sure that the parking brake is on and that the vehicle is in Park or Neutral, and then start the engine and check for leaks around the filter.
if the engine hard to start click here the link to follow steps how bleeding is done

Quick tips

  • Follow these instructions carefully. Read and be sure you understand them before you begin.
  • Gather all your tools and supplies before you begin.
  • Allow plenty of time to do the job so you don't have to hurry.
  • Remember that these are general instructions. For more detailed instructions pertaining to your specific vehicle, consult an appropriate repair manual.
  • Safety is important whenever you're working around machinery. Beware of hot objects, sharp instruments and hazardous materials.
  • Don't substitute tools unless you're sure you won't compromise either your safety or the performance of your vehicle.

    Conclusion

    Replacing a motorcycle fuel filter does not have to be done by a professional mechanic. In fact, do it yourself can complete the repairs themselves, as long as they take a few safety precautions and go through the replacement process carefully.
    The first step is knowing when a fuel filter should be replaced, and this depends on the type of motorcycle and the filter that has been installed.

The photo is for landini tractor diesel engine EGERTON UNIVERSITY
view my facebook page
Labels:

Comments

Post a Comment

Popular posts from this blog

How to slide in Word Procedure is useful for creating presentations on PCs without PowerPoint By Helito Beggiora, for TechTudo 08/04/2019 08:01 Updated há 16 horas You can create slides in Word with a few simple settings. The feature is useful if your PowerPoint application is in trouble and you need to produce a presentation in a hurry. To do this in the text editor, you need to make adjustments in the orientation and size of the sheets, change the margins, and manually insert titles and topics into large fonts. In the following tutorial, check out how to make slides in Word from the PC. The procedure was performed in the latest version of Office 2016 , but the tips are also valid for users of previous editions of the Microsoft program . Eight hidden functions of Word that will streamline your work How to insert line in Word Want to buy cell phone, TV and other discount products? Compare TechTudo Step 1. Open a new Word document and go to the "Layout" tab. Then go...
Post a Comment
Read more

Methods used for the calculation of areas in Surveying

Methods used for the calculation of areas in Surveying: Simpson’s rule Trapezoidal rule Graphical rule Simpson’s Rule Statement It states that, sum of first and last ordinates has to be done. Add twice the sum of remaining odd ordinates and four times the sum of remaining even ordinates. Multiply to this total sum by 1/3 rd of the common distance between the ordinates which gives the required area. Where O 1 , O 2 , O 3 , …. O n are the lengths of the ordinates x = common distance n = number of divisions Note: This rule is applicable only if ordinates are odd, i.e. even number of divisions. If the number of ordinates are even, the area of last division maybe calculated separated and added to the result obtained by applying Simpson’s rule to two remaining ordinates. Even if first or last ordinate happens to be zero, they are not to be omitted from Simpson’s rule. The following offsets are taken from a chain line to an irregular boundary toward...
Post a Comment
Read more

About creating partition

About creating partition To create partition is actually to partition hard drive. Only after you creating partition(s) on a disk, can you make use of the disk to save all kinds of data. All physical parameter of a disk are set when you create partition(s) on it, including MBR (Main Boot Record) and the destination for storing boot record backup. For other information later needed for the management of file system and other operating systems, it will be achieved by later advanced format. What are the advantages of creating partitions? Generally speaking, creating more than one partition enables you to have operating system separate from data, deploy multi-boot setups, and keep frequently used programs and data near each other. Therefore, you can manage your computer with ease. If there is only one partition (namely C drive) on disk: When recovering the system, the whole c disk (the system disk) will be formatted. If all data are saved in c disk, they will all be wiped a...
Post a Comment
Read more